OCZ Agility 3 重新开卡失败求助

5x5jc8 · 发表于 2016-3-29 00:26:58

１２０Ｇ　ＯＣＺ掉盘了就想从新开卡，但是总是刷不了固件。。。。。

另外这盘的Ｆ是大Ｓ　ＰＦ４１２　ＡＬ，我用老固件22214 ＳＦ－２２８１　１２０ＧＢ　Ｍｉｃｒｏｎ２５　ＭＬＣ　ＴＳＯＰ　１６ｘＭＴ２９Ｆ６４Ｇ０８ＣＢＡＡＡＷＰ，这个是对的么？

＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝[Sun 05/03/2015 10:23:30] - Instructing the operating system to purge any existing cached data for device: '1:0:0:0'
[Sun 05/03/2015 10:23:35] - Issuing a discovery command for device: '1:0:0:0'
[Sun 05/03/2015 10:23:42] - Discovery command completed...
[Sun 05/03/2015 10:23:42] - Waiting 5 seconds for the system to settle...
[Sun 05/03/2015 10:23:47] - Device designation string '1:0:0:0' is mapped to node '/dev/sg1'
[Sun 05/03/2015 10:23:47] - Proceeding to process SSD device with the following parameters:
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
            DeviceName = /dev/sg1
MFP Package Filename = /MPT/FW_SF-2000_MP_5-0-7_Client--1234/FW_SF-2000_MP_5-0-7_Client.1234.mfp
   Configuration File = /SOFT/22214.1234.V507.driveconfig
            Serial No. = 11114
      World Wide Name = 11114
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

[Sun 05/03/2015 10:23:47] - Successfully received the IDENTIFY data from the drive...
[Sun 05/03/2015 10:23:47] - Validating Manufacturing Firmware Package: /MPT/FW_SF-2000_MP_5-0-7_Client--1234/FW_SF-2000_MP_5-0-7_Client.1234.mfp
[Sun 05/03/2015 10:24:04] - Successfully opened the package: /MPT/FW_SF-2000_MP_5-0-7_Client--1234/FW_SF-2000_MP_5-0-7_Client.1234.mfp
[Sun 05/03/2015 10:24:04] - file  /SOFT/22214.1234.V507.driveconfig Loaded successfully
[Sun 05/03/2015 10:24:04] - Warning:  Unable to query diagnostics information to perform power management settings check
[Sun 05/03/2015 10:24:04] - B01 Power Management configuration request detected
[Sun 05/03/2015 10:24:04] - Successfully extracted *.DriveConfig file: /SOFT/22214.1234.V507.driveconfig
[Sun 05/03/2015 10:24:04] - Extracted Config_ID: 1 (22214) in DriveConfig file: /SOFT/22214.1234.V507.driveconfig
[Sun 05/03/2015 10:24:04] - Extracted SerialOutputControl: 0
[Sun 05/03/2015 10:24:04] - Searching for flashware image for configuration 22214
[Sun 05/03/2015 10:24:04] - Manifest found for configuration 22214
[Sun 05/03/2015 10:24:04] - Flashware image extracted: 22214_fw_cl_mlc_Micron_64Gb_MT29F64G08CBAAAWP_2Q_1C_1D_PP_R00751_s512.vic
[Sun 05/03/2015 10:24:04] - Searching for manufacturing image for configuration 22214
[Sun 05/03/2015 10:24:04] - Manifest found for configuration 22214
[Sun 05/03/2015 10:24:04] - Manufacturing image extracted: 22214_mf_mlc_Micron_64Gb_MT29F64G08CBAAAWP_2Q_1C_1D_PP_R00751_s512.vic
[Sun 05/03/2015 10:24:04] - Proceeding in ROM mode, download feature 3...
[Sun 05/03/2015 10:25:10] - FATAL_ERROR: Could not download MFB to the drive...(0x11000001:SF_SG_DEVICE_CHECK_CONDITION_ERROR)

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Extended Error data:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      ATA COMMAND : 0x0092  (146)
      ATA FEATURE : 0x0003  (3)
      Device Status: 0x0001  (1)
      Driver Status: 0x0000  (0)
         Host Status: 0x0008  (8)
~~~~~~~~~~~~~~
Sense Data:
~~~~~~~~~~~~~~
  0 -       No Sense: 114 (0x72) OK
  1 -  Recovered Error:  11 (0x0B) FAIL
  2 -       Not Ready: 0 (0x00) OK
  3 -    Medium Error: 0 (0x00) OK
  4 - Hardware Error: 0 (0x00) OK
  5 -  Illegal Request: 0 (0x00) OK
  6 - Unit Attention: 0 (0x00) OK
  7 -    Data Protect:  14 (0x0E) OK
  8 -    Blank Check: 9 (0x09) OK
  9 -  Vendor Specific:  12 (0x0C) OK
10 -    Copy Aborted: 0 (0x00) OK
11 -  Aborted Command: 0 (0x00) OK
12 - Equal Comparison: 0 (0x00) NA
13 -  Volume Overflow: 1 (0x01) NA
14 -    Miscompare: 0 (0x00) OK
15 -       Reserved: 224 (0xE0) NA
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
System Trace:
~~~~~~~~~~~~~~~~

[  545.671762] sd 1:0:0:0: [sdb] Add. Sense: No additional sense information
[  545.671803] ata2.00: disabled
[  550.668381] ata2.00: hard resetting link
[  550.972155] ata2.01: hard resetting link
[  551.977882] ata2.01: failed to resume link (SControl 0)
[  552.128764] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  552.128779] ata2.01: SATA link down (SStatus 0 SControl 0)
[  552.129051] ata2.00: ATA-8: SandForce{200026BB}, 20DABBR0, max UDMA/133
[  552.129055] ata2.00: 64 sectors, multi 0: LBA48 NCQ (depth 0/32)
[  552.132007] ata2.00: configured for UDMA/133
[  552.132018] ata2: EH complete
[  552.132169] scsi 1:0:0:0: Direct-Access    ATA    SandForce{200026 20DA PQ: 0 ANSI: 5
[  552.136601] sd 1:0:0:0: [sdb] 64 512-byte logical blocks: (32.7 kB/32.0 KiB)
[  552.136605] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[  552.136662] sd 1:0:0:0: [sdb] Write Protect is off
[  552.136666] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[  552.136689] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  552.137519]  sdb:
[  552.137866] sd 1:0:0:0: Attached scsi generic sg1 type 0
[  552.146856]  unknown partition table
[  552.147785] sd 1:0:0:0: [sdb] Attached SCSI disk
[  585.655010] ata2: lost interrupt (Status 0x58)
[  585.655030] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  585.655046] ata2.00: failed command: DOWNLOAD MICROCODE
[  585.655051] ata2.00: cmd 92/03:80:00:00:00/00:00:00:00:00/00 tag 0 pio 65536 out
[  585.655053]       res 40/00:01:e0:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[  585.655055] ata2.00: status: { DRDY }
[  585.655064] ata2.00: hard resetting link
[  585.959440] ata2.01: hard resetting link
[  586.965128] ata2.01: failed to resume link (SControl 0)
[  592.158485] ata2.00: link is slow to respond, please be patient (ready=0)
[  595.672987] ata2.00: SRST failed (errno=-16)
[  595.672997] ata2.00: hard resetting link
[  595.977600] ata2.01: hard resetting link
[  596.983327] ata2.01: failed to resume link (SControl 0)
[  602.176682] ata2.00: link is slow to respond, please be patient (ready=0)
[  605.691182] ata2.00: SRST failed (errno=-16)
[  605.691193] ata2.00: hard resetting link
[  605.995789] ata2.01: hard resetting link
[  607.001495] ata2.01: failed to resume link (SControl 0)
[  612.194862] ata2.00: link is slow to respond, please be patient (ready=0)
[  640.667450] ata2.00: SRST failed (errno=-16)
[  640.667464] ata2.00: hard resetting link
[  640.972054] ata2.01: hard resetting link
[  641.977759] ata2.01: failed to resume link (SControl 0)
[  645.694015] ata2.00: SRST failed (errno=-16)
[  645.694021] ata2.00: reset failed, giving up
[  645.694024] ata2.00: disabled
[  645.694049] ata2: EH complete
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

[Sun 05/03/2015 10:25:10] - End of Genesis manufacturing log.
[Sun 05/03/2015 10:25:10] - Exiting...

zzyye1 · 发表于 2016-3-29 00:26:59

507、522的22214似乎都是64GB:

5cwmkxxl · 发表于 2016-3-29 00:26:59

本帖最近评分记录：共条评分

回复举报

离线demiurge3141

UID：1862164注册时间2015-04-13 最后登录2015-12-18 在线时间27小时发帖37 搜Ta的帖子精华0 M币-300专家0 访问TA的空间加好友用道具

数码8级

发帖37M币-300专家0粉丝4加关注发消息只看该作者 6楼发表于: 2015-05-04

部分成功了。原来是主板问题。H61太新了，换了一片775主板就可以了。但是问题来了，128G的F只开出64G，这怎么解决？？？应该是固件错了。哪一个MT29F64G08CBAAA的固件是SF2281 120/128G的？我用了507的22214。

nv8np9 · 发表于 2016-3-29 00:26:59

有啊，认出sandforce盘了，但是一开始写入固件就失败

[  552.129051] ata2.00: ATA-8: SandForce{200026BB}, 20DABBR0, max UDMA/133
[  552.129055] ata2.00: 64 sectors, multi 0: LBA48 NCQ (depth 0/32)
[  552.132007] ata2.00: configured for UDMA/133
[  552.132018] ata2: EH complete
[  552.132169] scsi 1:0:0:0: Direct-Access    ATA    SandForce{200026 20DA PQ: 0 ANSI: 5
[  552.136601] sd 1:0:0:0: [sdb] 64 512-byte logical blocks: (32.7 kB/32.0 KiB)
[  552.136605] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[  552.136662] sd 1:0:0:0: [sdb] Write Protect is off
[  552.136666] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[  552.136689] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  552.137519]  sdb:
[  552.137866] sd 1:0:0:0: Attached scsi generic sg1 type 0
[  552.146856]  unknown partition table
[  552.147785] sd 1:0:0:0: [sdb] Attached SCSI disk

就是这里开始出错了。。。。

[  585.655010] ata2: lost interrupt (Status 0x58)
[  585.655030] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  585.655046] ata2.00: failed command: DOWNLOAD MICROCODE

chq6ssz · 发表于 2016-3-29 00:26:59

你是不是该选22189的配置文件啊

mo40x9h · 发表于 2016-3-29 00:27:00

本帖最近评分记录：共条评分

回复举报

离线demiurge3141

UID：1862164注册时间2015-04-13 最后登录2015-12-18 在线时间27小时发帖37 搜Ta的帖子精华0 M币-300专家0 访问TA的空间加好友用道具

数码8级

发帖37M币-300专家0粉丝4加关注发消息只看该作者 9楼发表于: 2015-05-04

对22189 开出120了，不过现在用着死机了。。

ntx89fq · 发表于 2016-3-29 00:27:00

另外教材里面说开卡失败短接 GPIO1 和 WP0就是一般短接认卡么？

z2df24q · 发表于 2016-3-29 00:27:00

内容短接插sata口，看看有没有认sandforce盘有了就打开开卡工具，开始写入固件了，就松开短接

j2512dsd · 发表于 2016-3-29 00:27:00

开卡前先短接。。。配置文件要选好。。。话说你也不发张图。。怎么指点你？

yi11l8 · 发表于 2016-3-29 00:27:01

请问要短接到什么时候？我都是开机过BIOS了就断了，进入系统lsscsi还是可以看到sandforce 盘，然后我跑开卡工具，都一路没有短接了。
F是大S PF412 AL 好像是镁光 MT29F64G08CBAAA的黑片。我用了507固件包里面的 22214固件。选错固件也会写不进去么？大S PF412 AL
要用哪一个？

		自动登录	找回密码
密码			立即注册